Screen printing Dielectrical ink Introduction:
integration capacitive screen (One Glass) Ink - Operating process instructions
Model: PIC-1075D black GTS insulated high temperature and pressure process
Performance Introduction: PIC-1075D high pressure and temperature insulation for insulating exclusive black black One Glass developed a resistance to 300 ℃, to avoid when conducting ITO coatings for high temperature
Generating a short circuit conductive. .
Scope: One Glass craft, GTS (monolithic) program. Professional for tempered glass substrate (Corning / Asahi pin / board pin / center pin of the other brands).
Advantages: 1, film thickness, 420 mesh screen printing two times, OD value of 6.0 or more, the thickness of 5-8um
2, excellent chemical resistance, resistance to alcohol and forth 500 times the force unchanged 500g, 500g force acetone did not change back and forth 20 times, after curing is now no longer dissolved
Like (Note: The abrasion testing machine).
3, ink granule delicate, particle fineness 4um less ink surface is extremely smooth, flat effect.
4, the ink film surface particle size distribution, and non-print textured water wave phenomena, ITO shot plating
Film formation, no cracks or pitting phenomenon does not affect the conductivity of ITO film.
5, with high temperature and high voltage insulation, which when the appropriate ITO sputtering and high temperature tempering properties and the necessary insulating properties.
Baking temperature / time change hue surface load voltage 250V 500V load voltage insulation value insulation value
300 ℃ / 30 minutes plain: no change in surface color ink 2000 IU/R more than 4000IU/R
Environmental Features: This product meets the ROSH, halogen, REACH, 16P and other environmental requirements
Conditions: PIC-1075D high pressure and temperature insulation OGS black ink, resistant to 300 ℃ bake 30 minutes of high insulation
1, ink characteristics: OGS Special Black, temperature 300 ℃ bake 30 minutes of high insulation
2, ink usage conditions:
2.1 (PIC-1075D): curing agent (PIC-1000 (G7)) = 100: 5, with P-800 Thinner: 2-5%
2.2 After completion stir the ink formulation (2-3 minutes) with a stirrer (500-800 rev / min). Stand for 10 minutes and then go to print.
2.3 Drying conditions: head color black: 200 ℃ 10 minutes
Note: This series is not completely dry black plus insurance, plus insurance otherwise no adhesion layer, 250 ℃ 40 minutes (completely dry)
Storage conditions: Ink: thermostat 25 ℃, 45% -65% humidity, sealed and stored away from direct sunlight. Sealed original shelf life 12 months
Curing agent: thermostat 25 ℃, 45% -65% humidity, sealed and stored away from direct sunlight. Sealed original shelf six months
Packing: Ink: 1KG / cans 4KG / tank curing agent: 100G / cans
Note: 1, before using ink, make sure that the substrate surface is dust or static electricity, and ensure that operating in ten thousand or 1000 clean room production environment.
2, the deployment of ink, when crude oil is not used, please sealed to avoid solvent evaporation. After curing agent access immediately sealed, avoid prolonged exposure to air
The absorption of moisture.
3, ultrasonic cleaning, temperature control 70-80 ℃, the final cleaning tank takes 3-5 minutes to slowly pull the glass frame to avoid residual drops of water marks on the glass
Trace cause printing Leis.
4, cleaning ink or screen with a 783 plate cleaner. Such as ink adhesion please use soapy water to clean the skin, eating or feeling uncomfortable, consult a doctor immediately.
5, use high-pressure water in case of fire, dry fog, no carbon dioxide, foam or dry chemical fire fighting, etc.. Other features please refer to "MSDS"